Quick Installation Guide
TEW-MP1U
1. Before You Start
Package Contents
?TEW-MP1U
?Quick Installation Guide
?Utility CD-ROM
?Power Adapter (12V, 1A)
System Requirements
?CD-ROM Drive
?CPU: 300Mhz or above/ 800Mhz or above (Windows Vista)
?Memory: 256MB RAM or above/ 512MB RAM or above (Window Vista)
?Windows 2000/XP/2003 Server/Vista (32bit)
Note:
1. Do not perform the following unless instructed to do so:
1. Install the utility
2. Connect printer to printer server
3. Connect computer to Print Server
2. The utility must be installed on each computer in order to use your multi-
function printer.
Application
1-Port Wireless G Multi-Function
USB Print Server
(TEW-MP1U)
Multi-Functional
USB 2.0 Printer
Workstation with
Wireless G PCI Adapter
(TEW-423PI)
Internet
Notebook with
Wireless G PC Card
(TEW-421PC)
Wireless G
Firewall Router
(TEW-432BRP)
Cable/DSL Modem
1
English
2. How to install
1. Install the printer drivers to your
computer. Then shutdown the
printer and disconnect the printer
from your computer.
Note: Please refer to your printer's manual for printer installation instructions.
2. Connect the Power Adapter to
the Print Server and then to a
power outlet.
3. Connect a RJ-45 network cable
from a Switch/Router to the LAN
port of the Print Server.
4. Connect the USB Printer to the
USB port of the Print Server.
5. Power ON printer.
6. Verify that the Status LED is lit on
the Print Server.
2
English
3. Configure the Print Server
1. Insert the Utility CD-ROM into your
CD-ROM driver. Then click Setup
Wizard.
2. Click Skip.
3. Select the print server and then
click Next.
3
English
4. Choose a wireless network to
connect to and then click Next.
5. Configure the IP address of the
print server to be in the same
subnet as your network and then
click Next.
6. Click Finish.
4
English
7. Click Yes.
8. Follow the InstallShield Wizard
instructions and then click Finish.
9. Click on Resource and then click
Connect.
10. The printer driver wizard appears.
Follow the printer driver wizard to
install the printer.
5
English
11. Click OK.
Print Server configuration is now complete.
For detailed information regarding the TEW-MP1U configuration and advanced
settings, please refer to the User's Guide on the Utility CD-ROM or
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
Thank you for choosing TRENDnet
6
English
4. Printing
Note: Only one user can use the print server at a time. Once a user has
finished using the print server, another user can use it.
1. Click on Resource and then click
Connect.
2. Status will now show the client
computer and IP address that is
currently using the printer.
3. User can now start printing.
4. Click Disconnect.
7
English
5. Faxing
Note: Only one user can use the print server at a time. Once a user has
finished using the print server, another user can use it.
1. Click on Resource and then click
Connect.
2. Status will now show the client
computer and IP address that is
currently using the printer.
3. User can now start Faxing. Follow
the Multifunction printer software
instructions for faxing.
4. Click Disconnect.
8
English
6. Scanning
Note: Only one user can use the print server at a time. Once a user has
finished using the print server, another user can use it.
1. Click on Resource and then click
Connect.
2. Status will now show the client
computer and IP address that is
currently using the printer.
3. Place the document on the Multi-
Function Printer's Scanner bed.
Then follow the Multifunction
printer software instructions for
scanning.
4. Click Disconnect.
9
English
Troubleshooting
Q1. The setup wizard/utility does not detect the Print Server and/or printer/storage device. What
should I do?
A1. First, double check your hardware connections; make sure that the Print Server and printer are
powered ON and are properly connected. Make sure the RJ-45 network cable is securely connected to
the Print Server and Switch/Router. Second, disable any software firewall programs such as ZoneAlarm
or Norton Internet Security. If your computer is running Windows XP or Vista, disable the built-in firewall.
Third, click Refresh. Fourth, power cycle the Print Server. Unplug the power to the Print Server, wait 15
seconds, then plug the Print Server back in.
Q2. The setup wizard/utility does not detect my printer device. What should I do?
A2. First, make sure the printer is powered on and properly connected to the Print Server. Second,
connect the printer with another USB cable. Third, reset the print server. Take a pin or paperclip and
press the reset button on the print server for 15 seconds, then let go.
Q3. I am unable to print to my print server. What should I do?
A3. First, make sure you follow the exact steps for installing the Print Server in section 2 Second, make
sure to right click on the print server in the utility and click connect. If another user is using the print
server, you must wait until the user is finished using it. Third, if you are connected to the print server and
are idled for a couple of minutes, a warning message appears. If you do not respond within a minute, you
will be automatically disconnected from the print server. You must connect to the print server again.
Q4. I can print a test page, but I cannot print anything from Microsoft Word or other applications.
A4. Make sure to set the newly installed network printer as your default printer. Click Start
and then click Printers & Faxes, verify that your printer icon has a check on it.
Q5. I configured my print server to automatically receive an IP Address from a DHCP server, and now I
cannot go into the print server’s web utility.
A5. Open the Print Server Set Up Wizard (See 3. Configure the Print Server) to locate
your print server’s IP Address.
Q6. Is there a way to force a computer to give up ownership of the print server?
A6. If the user has been idled for a few minutes, the user will be automatically disconnected.
Q7. After I successfully configured the TEW-MP1U to match my wireless network settings, I can not print
through the Print Server.
A7. First, verify that the wireless settings match your wireless network settings. Second, after configuring
your wireless network settings, make sure to unplug the power to the Print Server, disconnect the Ethernet
cable from the Print Server, wait 15 seconds, then plug the Print Server back in. Third, verify that the
WLAN LED on the Print Server is lit. Fourth, if you have enabled encryption on your wireless network,
find out the type of encryption (e.g. WEP, WPA-PSK) and encryption key. Then open up the setup wizard,
connect to the desired wireless network and enter the encryption key.
If you still encounter problems or have any questions regarding the TEW-MP1U, please refer to the User's Guide
included on the Utility CD-ROM or contact TRENDnet's Technical Support Department.
10
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentacón
necesario para su funcionamiento. El uso de un adaptador distinto al mencionado puede producir
daños fisicos y/o daños al equipo conectado. El adaptador de alimentación debe operar con voltaje y
frecuencia de la energia electrica domiciliaria existente en el pais o zona de instalación.
TRENDnet Technical Support
.
US Canada
Toll Free Telephone: 1(866) 845-3673
24/7 Tech Support
.
.
.
.
Europe (Germany France Italy Spain Switzerland UK)
Toll Free Telephone: +00800 60 76 76 67
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
Worldwide
Telephone: +(31) (0) 20 504 05 35
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
Product Warranty Registration
Please take a moment to register your product online.
20675 Manhattan Place
Torrance, CA 90501
USA
Copyright ©2007. All Rights Reserved. TRENDnet.
|